Recent Discussions in Club for owners and restorers of Bolens


To join this group, send a blank email to BolensTractorsClub-subscribe@yahoogroups.com or visit http://groups.yahoo.com/group/BolensTractorsClub



  1. Re: 1050 pto and drive belt length
    Thanks for the numbers. BTW, If belts don't match, they will fight each other wasting power and inflicting damage on themselves. This is because the longer...
    - Wed, 03 Dec 2008 17:38:52 GMT
  2. 1250 engine
    I have a husky 1250 tractor with a good running wisconsin 12hp engine and a plow the tractor does not move to well I am looking to get 300.00 for it. thakyou...
    - Wed, 03 Dec 2008 17:24:51 GMT
  3. Re: NEED A 1250 ENGINE
    Boat batteries may be a better buy if there is no road tax on it. The heaver the battery, the more energy it will store. Ed Stoller New Fairfield, CT ...
    - Wed, 03 Dec 2008 13:09:05 GMT
  4. Re: NEED A 1250 ENGINE
    Dominic, As was suggested in others replies, I used a small car battery mostly because it delivers enough power even in the worst winter condition, and the...
    - Wed, 03 Dec 2008 03:04:52 GMT
  5. Re: 1886 no compression in one cylinder
    Alice, I agree with Ray and Khenneth for their suggestions. You need the help from someone that can point to the specific problem. The K-482 has a compression...
    - Wed, 03 Dec 2008 02:37:38 GMT
  6. Re: Message to member "Hamr Hamr"...
    thanks for the response,  The G14 sold within a couple hours. take care.  hamr  ... From: Captain Jack Sparrow <capt_jacksparrow1020@...> Subject:...
    - Wed, 03 Dec 2008 02:32:36 GMT
  7. Re: 1050 pto and drive belt length
    ... the same convention as the drives  i.e.  174241 ... reference for you.  Make sure you size them up against one another because when I got mine the first...
    - Tue, 02 Dec 2008 19:54:46 GMT
  8. Message to member "Hamr Hamr"...
    I've looked all over eBay for the G14 you said you posted and cannot find it. Please send a link and info. Jack  "I do not feel obliged to believe that the...
    - Tue, 02 Dec 2008 19:20:42 GMT
  9. Re: 1050 pto and drive belt length
    Marty,   Drive belts are thirty four inches by 1/2"    Dayco 17341 GoodYear 17341 NAPA 9341 Gates 9341 International 17340   PTO belts are forty two by...
    - Tue, 02 Dec 2008 17:29:14 GMT
  10. 1050 pto and drive belt length
    I know this has been asked and covered before but I can't find it anywhere. I just blew the drive belts tonight on my 1050 and was wondering what the lengths...
    - Tue, 02 Dec 2008 01:12:42 GMT
  11. Re: 1886 husky-
    just listed my G14 on ebay for parts or restore.  OHV Tecumseh 14hp head went bad.  take care all. ... From: jim fear <jimmyboy762@...> Subject: Re:...
    - Sun, 30 Nov 2008 18:36:29 GMT
  12. Re: 1886 husky-
    where are u located and what would you want for it        jim in ct ... From: rjmartinny <no_reply@yahoogroups.com> Subject: [Bolens Tractors Club] Re:...
    - Sun, 30 Nov 2008 05:36:50 GMT
  13. Re: Drive Shaft Question?
    Still waiting for an answer.  Anyone know what the difference is? ... From: Garden Man Organic <lovethatbolens@...> Subject: Re: [Bolens Tractors Club]...
    - Sun, 30 Nov 2008 02:26:20 GMT
  14. Re: 1886 husky-
    ... You might want to fix that 1886, not a big job to replace input shaft [rotor] I can get you a new or used one, that Eliminator 17 in not the tractor your...
    - Sun, 30 Nov 2008 01:40:50 GMT
  15. Tube frame rears 3 speed versus 6 speed gears
    Are the gears the same between the 3 speed and 6 speed with the exception of the high/low side? I have a 6 speed that has no 2nd gear and I need to fix it (not...
    - Sun, 30 Nov 2008 01:32:49 GMT